Division 06
Industrial Materials
Materials that go into the built environment — a low-carbon rolled concrete we hold the representation for, engineered formwork and structural timber, industrial paper and packaging, and machinery on direct enquiry.
Concrete Roll — INNOBETON 21®
A concrete-filled polymer fabric supplied on rolls. Unroll it, fix it, hydrate it, and it cures into a hard-wearing concrete layer. No batching plant, no formwork, no vibration equipment, and no concrete truck that has to reach the site.
That last point is usually what sells it. On remote ground, difficult access or long linear works, the constraint is rarely the concrete — it is getting a mixer there before the load goes off.
- 5 mm
- 8 mm
- 11 mm
- Applications
- Erosion control and slope protection, channel and canal lining, oil storage carcasses and secondary containment, bridge cone reinforcement, ditch and culvert remediation.
- Why it is specified
- Up to ten times faster to install than a poured section, at a fraction of the cement volume — and installable where a batching plant cannot go.
- Commercial basis
- NJORD holds the representation for this material. Supplied by the roll against a defined scope of works.
Timber & wood products NJORD Wood Supply Division
Sawn, engineered and industrial wood from established CIS and European mills, kiln-dried where the grade requires it, in export packaging with grading certificates per parcel — delivered across the GCC and beyond.
- Softwood
- Spruce, pine and fir (whitewood / redwood), and Douglas fir — kiln-dried to 12% ± 2%, custom cross-sections, grades and lengths.
- Hardwood
- Oak, teak and mahogany for joinery and marine applications; birch and beech for furniture and interiors. Legality documentation (FLEGT / due-diligence per destination) supplied per parcel.
- Engineered wood
- Plywood in various grades including birch, film-faced and LNG cargo-containment grade; MDF; OSB; particleboard. Plus H20 glued formwork I-beams — 200 mm height, 80 mm flange, lengths 1.45–6.0 m, 20+ reuse cycles, to EN 13377 with plywood webs to EN 636-3, or destination-market equivalent confirmed per order.
- Industrial wood
- Wood chips for pulp and board production, and sawlogs / round logs by species and diameter class.
Paper & packaging
northern conifer fibre, industrial packaging and wood-derived chemistry. Sack kraft and industrial sacks are the volume lines; plywood and lignosulphonates are where the technical requirements sit.
- Kraft paper
- Cardboard & containerboard
- Valve, open-mouth & pinch-bottom sacks
- Greaseproof paper
- Birch plywood
- Film-faced plywood
- LNG-grade plywood
- Fibreboard
- Wood pellets
- Tall oil derivatives
- Lignosulphonates
- Cardboard
- Containerboard and corrugated grades for packaging converters, by GSM and burst strength per contract.
- Industrial sacks
- For cement and construction materials, chemicals, fertilisers, food and agriculture — converted from unbleached northern conifer kraft with high tensile and tear strength.
- Plywood
- Standard, film-faced, LNG cargo containment insulation grade, and flooring grades for transport and interiors.
- Lignosulphonates
- Powder and liquid, for concrete plasticising, dust suppression, feed binding and ceramics.
- Wood pellets
- ENplus-referenced quality for industrial and residential biomass heating and co-firing.
Industrial chemicals
Sodium bicarbonate, ammonium chloride, sodium nitrate, non-concentrated nitric acid (HNO₃ 57–60%), technical sulfuric acid, synthetic hydrochloric acid and gaseous CO₂ are supplied through our chemicals desk, with SDS and transport classification per line.
- Full detail
- See Chemicals — mineral acids, industrial salts and gases, and controlled mining chemicals, each with its documentation and handling basis.
Machinery & equipment
Used machinery, new spare parts and vehicles on direct enquiry. Sourced to order against a defined requirement rather than held in stock — send the specification, budget and destination and we revert with availability, condition reports and a delivered cost.
- Used machinery
- New spare parts
- Vehicles
- Used machinery
- Construction, agricultural and industrial. Make, model, hours, condition and pre-purchase inspection arranged before commitment.
- Spare parts
- OEM and equivalent, matched by part number and serial-range compatibility.
- Vehicles
- Commercial and personal, sourced to specification with export documentation and shipping arranged.
Enquiries
Every enquiry is answered by a trader.
Send the product, quantity, delivery basis, destination and timing. We revert with availability, an indication and the documentation that accompanies it. Specifications are released once we know who we are speaking with.